-
Sale is now on up to 40% off Shop Now
-
Sale is now on up to 40% off Shop Now
-
Sale is now on up to 40% off Shop Now
-
Sale is now on up to 40% off Shop Now
Home / Gunsmithing
Gunsmithing
Don't live in our area but want to use our services? Don't worry, you can ship your firearm to us. Click on the button below for more information
SERVICE CHARGES
- - We reserve the right to refuse any work that the gunsmith deems would make the firearm unsafe.
- - We WILL NOT ​remove or disconnect any firearm safety and/or any component that would cause the firearm to violate federal and/or state laws.
- - Service prices do not include parts or materials.
- - Service prices subject to change depending on difficulty of job.
GUNSMITHING - REPAIRS
-
Hourly Rate - Man Hours
-
Hourly Rate - Man/Machine Hours
-
Minimum Charge Per Firearm
-
Written Cost Estimate
- Free if we perform the work
GENERAL
- Barrel Inspection (Borescope)
- - 20 caliber and above only
- Chamber Cast
-
- Clean and Inspect
- - Revolvers/Pistols
- ​- Rifles/Shotguns
- Drill & Tap
- - Aluminum/Steel
- - Hardened Metal
- Lap Bore
-
- Muzzle Device
- - Install (Pre-threaded barrel)
- - Pin/Weld
- Polsih Chamber
-
- Remove Stuck Case / Bore Obstruction​
- ​Throat & Feed Ramp Polish
- - Improves feeding reliability
AR-10/AR-15
- Assemble
- - Upper
- - Lower
- - Complete Rifle
- Cut/Polish Feed Ramps
-
- Dimple Barrel for Gas Block
- - Add $40 for Disassemble/Reassemble
- Install Gas Block & Dimple Barrel
-
- Install Rear Sling Plate
-
- Install Trigger
-
- Replace Gas Rings
-
- Replace Gas Tube
-
- Replace Buffer Tube
-
- Stake Castle Nut
-
​*Price is determined by difficulty of disassembly/reassembly
FINISHING
​*Price is determined by number of parts
- Abrasive/Bead Blast/Wire Wheel (Matte)
-
- Deluxe Finish (Hand sanding up to 400 grit):
- - Handguns
- - Rifles/Shotguns
- Draw Filing
-
- ​Parkerize - Manganese (Includes Metal Prep)
- - Handguns
- - Rifles/Shotguns
- ​Slow Rust Bluing (Includes Metal Prep)
- - Handguns
- - Rifles/Shotguns
TRIGGER WORK
- Trigger Kit Installation (Drop-In)
- - Additional cost if inletting required
- ​Trigger Job aka "Smooth & Tune"
- - Revolvers
- - Semi-Auto Pistols
- - Rifles
- ​Trigger Pull Reduction / Spring Kit Installation
SIGHT WORK
- Bore sighting - Standard Scopes w/ Collimator
- - Simulates 100 yards
- ​Front Sight Ramp - Screw On (Drill & Tap)
-
- Remove/Install
- - Dovetail
- - Staked
- - M1 Carbine (Front/Rear)
- ​Scope Mounting​
- - Lap Rings
- - Mount and Boresight
- ​Shotgun Bead, Front/Mid (Drill & Tap)
STOCK WORK
- Clean & Oil Finish:
- - Hand Rubbed (Unfilled Grain)
- - Hand Rubbed (Filled Grain)
- Complete Refinishing
- - Sand, Stain, Raise Dents, Oil
- Inlet / Fit Stock
-
- ​Recoil Pad Installation
- - Grind-to-fit
- - Standard (add $40 if drilling required)
- Sling Swivel Installation (Drill Stock)
-
​*Price is determined by complexity of stock
MACHINE WORK
- Barrel Threading $175
-
- Milling Hourly Rate - Machine
Please contact us about any service not listed above.
Information